Trang chủ » IIoT » Bộ lập trình IoT 10 kênh đầu vào tương tự (AI) + 3 kênh DO + 2 cổng Ethernet ICP DAS WISE-7519ZM/S2 CR

Bộ lập trình IoT 10 kênh đầu vào tương tự (AI) + 3 kênh DO + 2 cổng Ethernet ICP DAS WISE-7519ZM/S2 CR

Intelligent MQTT I/O Module with 10-ch AI, 3-ch DO and 2-port Ethernet Switch

Chia sẻ:
Model: WISE-7519ZM/S2 CR
Views: 1083

Bộ lập trình IoT 10 kênh đầu vào tương tự (AI) + 3 kênh DO + 2 cổng Ethernet ICP DAS WISE-7519ZM/S2 CR

WISE (Web Inside, Smart Engine) is a product series developed by ICP DAS that functions as control units for use in remote logic control and monitoring in various industrial applications. WISE offers a user-friendly and intuitive web site interface that allows users to implement IF-THEN-ELSE control logic on controllers just a few clicks away; no programming is required. With its powerful and easy-to-use features, it will minimize the learning curve, shorten time to market and dramatically reduce the labor and cost spent on system development.

WISE-7519ZM is specifically designed for extremely accurate thermocouple measurement and features automatic cold-junction compensation for each channel to ensure temperature output consistency and stable temperature output in the field. Current input and voltage input are both supported. Open thermocouple detection and ESD/ EFT/Surge protection mechanisms are also included. The three digital output channels can be set as alarm outputs. WISE-7519ZM follows IEEE 802.3af-compliant Power over Ethernet (PoE) specification. It allows receiving power from PoE enabled network by Ethernet pairs. In additional to this, WISE-7519ZM also has a built-in two-port Ethernet switch to implement daisy-chain topology. The cabling is much easier and total costs of cable and switch are significantly reduced.

By integrating with IF-THEN-ELSE rule engine, WISE-7519ZM provides powerful functions such as I/O Monitoring/Control, Counter, Timer, Schedule, E-mail sending & CGI Command sending for use in various industrial applications. WISE-7519ZM also supports Modbus TCP and MQTT protocols to make seamless integration with SCADA, IT and IoT (Internet of Things) system.

  • Building Automation
  • Factory Automation
  • Machine Automation
  • Remote Maintenance
  • Remote diagnosis and Testing Equipment
  • etc.
Thermocouple Input
Channels 10 (Differential)
Input Type ±15 mV, ±50 mV, ±100 mV, ±150 mV, ±500 mV, ±1 V, ±2.5 V, ±5 V, ±10 V
±20 mA, 0 to 20 mA, 4 to 20 mA (Jumper Selectable)
Thermocouple (J, K, T, E, R, S, B, N, C, L, M, and LDIN43710)
Resolution 16-bit
Sampling Rate 10 Samples/Second (Total)
Accuracy ±0.1% of FSR or better
Zero Drift ±0.5 μV/°C
Span Drift ±25 ppm/°C
Over Voltage Protection 240 Vrms
Input Impedance >300 kΩ
Common Mode Rejection 86 dB Min.
Normal Mode Rejection 100 dB
Temperature Output
Stable Temperature Output in
the Field
Open Wire Detection Yes
Virtual Channel to Channel
±400 VDC
Digital Output
Channels 3
Type Isolated Open Collector
Sink/Source (NPN/PNP) Sink
Max. Load Current 650 mA/Channel
Load Voltage 5 VDC to 50 VDC
Overvoltage Protection 60 VDC
Overload Protection 1.4 A
Short-circuit Protection Yes
Ethernet Port 2 x RJ-45, 10/100 Base-TX, Swtich Ports
PoE Yes
Protocol Modbus TCP, MQTT
LED Indicators
for System Running Yes
for Ethernet Link/Act Yes
for I/O Channel Status Yes
for PoE Power Yes 
2-Way Isolation
I/O 2500 VDC
EMS Protection
ESD (IEC 61000-4-2) ±4 kV Contact for Each Terminal and
±8 kV Air for Random Point
EFT (IEC 61000-4-4) ±2 kV for Power Line
Surge (IEC 61000-4-5) ±2 kV for Power Line
Reverse Polarity Protection Yes
Powered from Terminal Block 12 to 48 VDC
Powered from PoE Yes, IEEE 802.3af, Class1
Consumption 3.6 W (Max.)
Dimensions (L x W x H) 114mm x 97mm x 38mm
Installation Wall mounting
Operating Temperature -25 °C to +75 °C
Storage Temperature -30 °C to +80 °C
Humidity 10 to 90% RH, non-condensing
Rule Configuration Website Access Web server on WISE controllers to edit and upload logic rules through web browser.
72 IF-THEN-ELSE Logic Rules 3 IF conditions with AND or OR operators
3 THEN actions and 3 ELSE actions
48 Internal Registers Hold temporary variables and read/write data
24 Timers Delay / Timing functions.
24 Schedules Setup prescheduled routine tasks.
24 Emails Send Email messages to pre-set Email receivers.
24 CGI Commands Send pre-set CGI commands.
24 Recipes Set up THEN/ELSE action groups.
8 P2P remote modules Set up the connection information for the remote WISE modules.
Modbus TCP Protocol Real time control and monitoring I/O channels and system status of controllers via SCADA software.
MQTT Protocol Real time message publish/subscribe mechanism for I/O channels and system status via IT/IoT software.
IF Conditions
AI Channel = 、> 、< 、 ≥ 、 ≤ (value)
Internal Register
DO Counter = 、> 、< 、 ≥ 、 ≤ (value), Change
Timer Timeout, Not Timeout
Schedule In Range, Out of Range
P2P DI, AI, DI counter, DO counter, IR
Rule Status Enable, Disable
THEN / ELSE Actions
DO Channel ON, OFF, Pulse Output
Internal Register Change the value
DO Counter Reset
Timer Start, Reset
Schedule Enable, Disable
Email Send
MQTT message
CGI Commands
Recipe Execute
P2P DO(On/Off), AO, IR
Rule Status Enable, Disable
WISE-7519ZM/S2     CR Intelligent I/O Module with 2-port Ethernet Switch, 10-ch AI, 3-ch DO and PoE. Supports Modbus/TCP and MQTT (RoHS)
Includes DB-1822 Daughter Board and 1.8 m Cable
  • GPSU06U-6 : 24 V/0.25 A, 6 W Power Supply
  • MDR-20-24 : 24 V/1 A, 24 W Power Supply with DIN-Rail Mounting
  • NS-205 CR : Unmanaged 5-Port Industrial Ethernet Switch (RoHS)
  • NS-205PSE CR : Unmanaged 5-Port Industrial PoE Ethernet Switch (RoHS)