Trang chủ » Remote I/O Module and Unit » Module Ethernet Modbus TCP 2 kênh DI + 2 kênh DO ICP DAS tET-P2A2 CR

Module Ethernet Modbus TCP 2 kênh DI + 2 kênh DO ICP DAS tET-P2A2 CR

Tiny Ethernet Module with 2-ch DI and 2-ch Source-type DO

Chia sẻ:
Model: tET-P2A2 CR
Views: 376

Module Ethernet Modbus TCP 2 kênh DI + 2 kênh DO ICP DAS tET-P2A2 CR

Providing various digital I/O functions, the tET/tPET series is an IP-based Ethernet I/O monitoring and control module. The module can be remotely controlled through a 10/100 M Ethernet network by using Modbus TCP protocol. Modbus has become a de facto standard communications protocol in industry, and is now the most commonly available means of connecting industrial electronic devices. This makes the tET/tPET series perfect integration with the HMI, SCADA, PLC and other software systems. The functionality of the tET/tPET series is almost the same as the ET-7000/PET-7000 series. The tET/tPET series tiny Ethernet I/O modules support various I/O types, like photo-isolated digital input, relay contact, photoMOS relay, and open-collector output. The module can be used to create DI to DO pair-connect through the Ethernet. Once the configuration is completed, the tET/tPET series module can poll the status of the local DI channels and then use the Modbus/TCP protocol to continuously write to a remote DO device in the background.

The tET/tPET series provides dual watchdog: CPU watchdog and host watchdog. The CPU watchdog automatically resets it-self when the built-in firmware runs abnormally. The host watchdog monitors the host controller (PC or PLC), and the output of the module can go to predefined state (safe value) when the host fails.

For maximum space savings, the tET/tPET series is offered in an amazing tiny form-factor that makes it can be easily installed in anywhere, even directly embedded into a machine. It is equipped with two removable terminal block connectors for easy wiring, and features a powerful 32-bit ARM MCU to handle efficient network trafficking. The tPET series offers true IEEE 802.3af-compliant (classification, Class 1) Power over Ethernet (PoE) using a standard category 5 Ethernet cable to receive power from a PoE switch like the NS-205PSE. When there is no PoE switch on site, the tPET series accepts power input from DC adapter.

  • Factory, Building and Home Automation
  • Remote Maintenance
Models tET-P2C2/tET-P2A2 tPET-P2C2/tPET-P2A2
System
CPU 32-bit MCU
Dual Watchdog Yes
Communication
Ethernet Port 10/100 Base-TX, 8-Pin RJ-45 x1,
(Auto-negotiating, Auto-MDI/MDIX, LED indicator)
PoE (IEEE 802.3af, Class 1)
LED Display
S1 PoE indicator (Green)
System indicator (Red)
E1 Link/Act indicator (Green)
10/100 M indicator (Yellow)
Mechanical
Dimensions 52 mm x 27 mm x 98 mm
Installation DIN-Rail mounting
Environment
Operating Temperature -25 °C ~ +75 °C
Storage Temperature -30 °C ~ +80 °C
Humidity 10 ~ 90 % RH, non-condensing
Power Requirements
Power Input PoE: IEEE 802.3af, Class 1
Terminal block: +12 ~ 48 VDC (non-regulated)
Power Consumption
Models tET-P2C2/tPET-P2C2 tET-P2A2/tPET-P2A2
Digital Input
Input Channels 2
Input Type (Device) Wet Contact (Sink, Source)
On Voltage Level +10 VDC ~ +50 VDC
Off Voltage Level +4 VDC max.
Input Impedance 10 k Ohm
Counters Max. Count 4,294,967,285 (32 bits)
Min. Pulse Width 0.15 ms
Frequency Measurement 3.5 kHz (without filter)
Overvoltage Protection +70 VDC
Isolation 3750 Vrms
Digital Output
Output Channels 2
Output Type (Module) Sink, Open Collector (NPN) Source, Open Collector (PNP)
Output Voltage +5 VDC ~ +30 VDC +10 VDC ~ +40 VDC
Max. Load Current 100 mA/channel 650 mA/channel
PWM 100 Hz Max. (High/Low duty cycle range = 5 ~ 65,535 ms)
Over-Voltage +60 VDC +48 VDC
Short Circuit Protection Yes
Output Isolation 3750 Vrms

Note: Because the characteristic of relay, the relay-type modules are not suitable to use PWM for a long time.

tET-P2A2     CR Tiny Ethernet Module with 2-ch DI and 2-ch Source-type DO (PNP) (RoHS)

PETL7000/tET/tPET Series Main Page

TOP HOME