Trang chủ » Bo mạch I/O kết nối máy tính (PC Boards) » Card PCI 1 cổng CAN ICP DAS PISO-CM100U-T CR

Card PCI 1 cổng CAN ICP DAS PISO-CM100U-T CR

1-port CAN Programmable Universal PCI Card

Chia sẻ:
Model: PISO-CM100U-T CR
Views: 352

Card PCI 1 cổng CAN CPU Intel Core 2 Duo 2.00 GHz OS Windows XP SP 3 ICP DAS PISO-CM100U-T CR

The CAN (Controller Area Network) is a serial communication protocol, and efficiently supports distributed real-time control with a very high level of security. It is an especially suited for networking “intelligent” devices as well as sensors and actuators within a system or sub-system. In CAN networks, there is no addressing of subscribers or stations in the conventional sense, but instead prioritized messages are transmitted.

ICP DAS provides an open architecture platform for CAN bus PISO-CM100/100U. The PISO-CM100/100U represents a very powerful and economic solution of an active CAN board with one CAN channels, covering a wide range of CAN applications. The 16-bit on-board microcontroller allows, among many other features, the filtering, preprocessing, and storage (with timestamp) of CAN messages as well as the real-time transmission of CAN messages. PISO-CM100/100U also uses the new Phillips SJA1000T and Transceiver 82C250/251, which provide bus arbitration and error detection with auto correction and re-transmission function. Under the effect of the powerful microcontroller, this card can be made for one CAN controller without losing data, even in systems with a high bus load. Besides, equipped with integrated intelligence functions, the PISO-CM100/100U makes it is possible to preprocess CAN data streams, thus relieving the PC of a considerable burden. As a result, real-time requirements on the PC applications are drastically reduced. Due to the state-of-the-art, it can be installed in a slot of 32-bits PCI bus or Universal PCI bus and supported truly “Plug & play” technology.

In addition, users can develop their own CAN application by using the PISO-CM100/100U library. When the PISO-CM100/100U is active, the data exchange between users’ application and can bus firmware is performed via the memory mapping method of the PISO-CM100/100U.

The PM-213x-CAN series power meter provides the CAN bus interface for users to easily gather the real-time power consumption information in their CAN applications. The PM-213x-CAN provides the Auto-Response mode which responses messages at regular intervals automatically. It makes the communication more efficient when collecting a lot of remote power information. The polling mode offers the precise information of every step required by the monitors. In addition, the PM-213x-CAN also owns the arbitration mechanism which can avoid data collision and error detection.

CAN bus Features:
  • NXP TJA1042 CAN transceiver
  • Follow CiA CAN 2.0B specification
  • Support Auto-Response mode and Polling mode
  • Support baud rate 125 kbps, 250 kbps and 500 kbps
  • Support up to 255 nodes on the CAN network
  • 2500 Vrms isolation on CAN port
  • 4 kV ESD protection on CAN port
  • CAN bus provides better capability in noise suppression
  • Support arbitration mechanism to avoid collision
  • Support error detection and error correction on CAN bus

Link to Power Meter page…

PC based Solution

ICP DAS has been developing various CAN products for several years, including PCI interface, converter, uPAC and slot module CAN products. In addition, we can provide CAN bus solution for our customers. Applying the PM-213x-CAN into the PC based system, the user could use general CAN converter or PCI CAN boards. Nowadays, the PISO-CM100U with power meter firmware inside would be the better choice. The power meter firmware manages all the PM-213x-CAN power meters and collects all power data automatically. We provide the development API and management utility which is shown as the following picture.

Download …

Test development:
OS:Windows XP SP 3
CPU:Intel Core 2 Duo 2.00 GHz
RAM:512 MB

Baud Rate(bps)
CAN 2.0 A
CAN 2.0 B
Frame per sec.
Frame per sec.
1000 k
7502
6589
800 k
6188
5258
500 k
4097
3451
250 k
2140
1801
125 k
1098
920
50 k
440
371
20 k
176
148
10 k
88
74

Note:The test result is the average value of receiving 100000 CAN messages

Windows Drivers:

  • Development Toolkit for Windows 2000/XP/7(32-bit/64/bit OS)
  • Demos for VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0
  • Demos for C#

Windows Tools:

  • CANUility (Include send/receive CAN messages, message ID filter, data format transformation, messages recoder and firmware update functions)
  • Debug tool

MiniOS7 Tools:

  • C/C++ Library for RTC, EEPROM, LED, DPRAM, CAN controller and timers control functions
  • Demos for TC, TC++, BC and BC++
Model Name
PISO-CM100U-D
PISO-CM100U-T
Hardware
CPU
80186, 80 MHz or compatible
SRAM/Flash/EEPROM
512 KB / 512 KB / 16 KB
DPRAM
8 KB
NVRAM
31 bytes (battery backup, data valid for up to 10 years)
RTC (Real Time Clock)
Yes
Bus Interface
Type
Universal PCI, 3.3 V and 5 V, 33 MHz, 32-bit, plug and play
Board No.
By DIP switch
CAN Interface
Controller
NXP SJA1000T with 16 MHz clock
Transceiver
NXP 82C250
Channel number
1
Connector
9-pin male D-Sub
5-pin screwed terminal block
Baud Rate (bps)
10 k, 20 k, 50 k, 125 k, 250 k, 500 k, 800 k, 1 M (allow user-defined baud rate)
Isolation
3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminal Resistor
Jumper for 120 Ω terminal resistor
LED
Round LED
Rx/Tx LED, ERR LED
Power
Power Consumption
300 mA @ 5 V
Software
Driver
Windows XP/7/8/10 (32-bit/64-bit OS),  InduSoft
Library
VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C# 2008
Mechanism
Dimensions
138mm x 22mm x 105mm (W x L x H)
Environment
Operating Temp.
0 ~ 60 ℃
Storage Temp.
-20 ~ 70 ℃
Humidity
5 ~ 85% RH, non-condensing
PISO-CM100U-T     CR 1-port Programmable CAN Universal PCI Card with 5-Pin Screw Terminal Connector (RoHS)
TOP HOME