Trang chủ » Remote I/O Module and Unit » RS-485 I/O Modules » I-7000 » Module RS-485 DCON & Modbus RTU 1 kênh đầu vào RTD + 2 kênh DO + 1 kênh DI ICP DAS I-7013 CR

Module RS-485 DCON & Modbus RTU 1 kênh đầu vào RTD + 2 kênh DO + 1 kênh DI ICP DAS I-7013 CR

1-ch RTD Input Module

Chia sẻ:
Model: I-7013 CR
Views: 786

Module RS-485 DCON & Modbus RTU 1 kênh đầu vào RTD + 2 kênh DO + 1 kênh DI ICP DAS I-7013 CR

The I-7013(D) and M-7013P(D) is a 1-channel RTD Input module that is used for measuring temperatures via an RTD sensor and supports Pt100, Ni120, and Pt1000 type sensors. The module allows 2/3/4-wire RTD connections and features open wire detection. In addition, the I-7013(D) and M-7013P(D) also includes 3000 VDC intra-module isolation and supports lead resistance elimination for 3/4-wire connections. The M-7013P and M-7013PD added support for 1-channel digital input as 50 Hz event counter and 2-channel digital output as high/low alarm. The M-7013P and M-7013PD support both the Modbus RTU and DCON protocols, which can be configured via software.
  • Tự động hóa tòa nhà
  • Tự động hóa nhà máy
  • Máy tự động
  • Bảo trì từ xa
  • Chẩn đoán từ xa
  • Kiểm tra trang thiết bị
Models I-7013 I-7013D M-7013P M-7013PD
RTD Input Module
Channels 1
Wiring 2/3/4-wire
Sensor Type Pt100, Pt1000, Ni120
Resolution 16-bit
Accuracy ±0.05%
Sampling Rate 10 Hz
Individual Channel Configuration No
Overvoltage Protection ±5 VDC ±120 VDC
Open Wire Detection Yes
3-wire RTD Lead Resistance Elimination Yes
Resistance Measurement 3.2 kΩ Max.
Digital Input
Channels 1
Sink/Source (NPN/PNP) Source, Dry Contact
ON Voltage Level Close to GND
OFF Voltage Level Open
Counter(50 Hz, 16-bit) Yes
Overvoltage Protectio ±30 VDC
Digital Output
Channels 2
Type Open Collector, MOSFET
Sink/Source (NPN/PNP) Sink
Load Voltage 3.5 ~ 50 VDC
Max. Load Current 700 mA/Channel
Overvoltage Protection 60 VDC
Overload Protection 1.4 A (with Short-circuit Protection)
Power-on Value Yes
Safe Value Yes
Models I-7013 I-7013D M-7013P M-7013PD
Communication
Interface RS-485
Bias Resistor No (Usually supplied by the RS-485 Master. Alternatively, add a tM-SG4 or SG-785.)
Format (N, 8, 1) (N, 8, 2) (E, 8, 1) (O, 8, 1)
Baud Rate 1200 to 115200 bps
Protocol DCON DCON Modbus/RTU
Dual Watchdog Yes, Module (1.6 Seconds), Communication (Programmable)
LED Indicator/Display
System LED Indicator Yes, 1 as Power/Communication Indicator
I/O LED Indicator
7-Segment LED Display Yes Yes
Isolation
Intra-Module Isolation, Field-to-Logic 3000 VDC
EMS Protection
ESD (IEC 61000-4-2) ±2 kV Contact for each Terminal ±4 kV Contact for each Terminal and 8 kV Air for
random point
EFT (IEC 61000-4-4) ±4 kV to Power Line
Surge (IEC 61000-4-5) ±0.5 kV for Power Line
Power
Reverse Polarity Protection Yes
Input Range +10 ~ +30 VDC
Consumption 0.7 W 1.3 W 0.6 W 1.2 W
Mechanical
Dimensions (L x W x H) 123 mm x 72 mm x 35 mm
Installation DIN-Rail or Wall Mounting
Environment
Operating Temperature -25 to +75°C
Storage Temperature -40 to +85°C
Humidity 10 to 95% RH, Non-condensing
I-7013     CR 1-ch RTD Input Module using DCON Protocol (Blue Cover) (RoHS)
tM-7520U CR RS-232 to RS-485 converter (RoHS)
tM-7561 CR USB to RS-485 converter (RoHS)
tM-SG4 CR RS-485 Pull-high/Pull-low and Termination Resistor Module (RoHS)
I-7514U CR 4-channel RS-485 Hub (RoHS)
SG-770 CR 7 channel differential or 14 channel single-ended surge protector (RoHS)
SG-3000 Series Signal Conditioning Modules for Thermocouple, RTD, DC Voltage, DC Current and Power Input Transformers
TOP HOME