Modbus TCP/UDP to HART Gateway (for -40 ℃ application)
Đặc tính
Bộ chuyển đổi RTU/ASCII sang HART ICP DAS HRT-711-UTA CR
• Support HART Short/Long frame
• Support HART Burst mode
• Allow two HART Masters
• Working in point-to-point or multi-drop HART mode
• Connecting up to 15 HART modules
• Support Modbus TCP/UDP server
• Support Modbus Slave mode
• Support firmware update via Com Port
• Support on-line replacement of HART devices
• Support acquire Long Frame Address automatically
• Provide LED indicators
• Built-in Watchdog
• Mountable on DIN Rail
Bộ chuyển đổi RTU/ASCII sang HART ICP DAS HRT-711-UTA CR
The HRT-711-UTA Gateway is specially designed for the master device of HART protocol. It allows the Modbus master to access the HART devices. These HART devices may be a transmitter, an actuator and so forth. In addition, we also provide the utility software for users to configure the HRT-711-UTA. By using this module, users can integrate their HART devices into Modbus network easily.
• Industrial Automation
• Factory Automation
• Process Automation
• Etc…
| COM Ports | |
|---|---|
| Ports | RS-232(3 wires) |
| Ethernet | |
|---|---|
| Ports | 10/100Base-TX Ethernet Controller (Auto-negotiating, Auto_MDIX) |
| HART | |
|---|---|
| Ports | 1 |
| Device | 2-wired or 4-wired HART devices |
| Topology | Point to Point or Multi-Drop |
| Data | Only Digital Data |
| Frame Type | Short and Long Frame |
| Burst Mode | Supported |
| Max. HART Device | 15 |
| Loop Resistor | 250 Ω resistor by Jumper |
| Isolation | UL1577 Spec. |
| Protocol | 2-pin screwed terminal block |
| Power | |
|---|---|
| Reverse Polarity Protection | Power reverse polarity protection, Over-voltage brown-out protection |
| Input Range | Unregulated +10 ~ +30 VDC |
| Consumption | 1 W |
| Mechanical | |
|---|---|
| Dimensions (mm) | 72 x 35 x 121 (W x L x H) Detail |
| Installation | DIN-Rail or Wall Mounting |
| Environmental | |
|---|---|
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -40 ~ +75 °C |
| Humidity | 5% ~ 95% RH, Non-condensing |
Support the following Modbus commands.
| Code | Name | Description |
|---|---|---|
| 01 | Read Coil Status | Read the ON/OFF status of discrete outputs in the slave |
| 02 | Read Input Status | Read the ON/OFF status of discrete inputs in the slave |
| 03 | Read Holding Registers | Read the binary contents of holding registers in the slave |
| 04 | Read Input Registers | Read the binary contents of input registers in the slave |
| 05 | Force Single Coil | Write a single output to either ON or OFF in the slave |
| 06 | Preset Single Register | Write an integer value into a single register in the slave |
| 15 | Force Multi. Coils | Write each coil in the sequence of coils to either ON or OFF in the slave |
| 16 | Preset Multi. Registers | Write a block of contiguous registers in the slave |
| HRT-711-UTA CR | Modbus TCP/UDP to HART Gateway (RoHS) (for -40 ℃ application) |
| CA-002 | DC connector to 2-wire power cable, 0.3 M |
| CA-PC09F | DB-9 Female connector with plastic cover |
| CA-0910N | DB-9 Female-Female 3-wire Null Modem Cable, 1 M |
| CA-0915 | Male DB-9 to Female DB-9 Cable, 1.5 m |
| CA-0910F | Female DB-9 to Female DB-9 Cable, 1.0 m |
| CA-0909 | Female DB-9 to Female DB-9 connector for tDS-712/tGW-712. |
| NS-205A CR | Unmanaged 5-port Industrial Ethernet Switch with Power Input +12 VDC ~ +56 VDC (RoHS) |
| NS-205PSE CR | Unmanaged Ethernet Switch with 4 PoE Ports and 1 RJ-45 Uplink (RoHS) |
| FRA05-S12-SU | 12 V/0.58 A (max) Power Supply. |
