Trang chủ » Truyền thông công nghiệp » Fieldbus Communication » Bộ chuyển đổi cổng J1939 sang Modbus RTU Slave ICP DAS GW-7228-G CR

Bộ chuyển đổi cổng J1939 sang Modbus RTU Slave ICP DAS GW-7228-G CR

J1939/Modbus RTU Slave Gateway

Tính năng

Bộ chuyển đổi cổng J1939 sang Modbus RTU Slave ICP DAS GW-7228-G CR

  • Provide PWR / J1939 / MODBUS indication LED
  • Built-in jumper to select 120 ohm terminal resistor
  • Watchdog inside
J1939 Features
  • Transmission and reception of all types of J1939 messages, including PDU1, PDU2, broadcast and destination specific
  • J1939 Transport Protocol for transmission and reception of large messages (9 – 1785 bytes)
  • Supported BAM of Connection Management Message
  • Network addresses management
Modbus RTU Features
  • Support RS-232, RS-485 and RS-422
  • interfacesSupported Modbus RTU slave protocol
  • Configurable for Modbus Network ID(1~250)
  • Configurable baud rates of 9600, 19200, 38400, 57600, 115200 bps
  • Configurable for no, odd, or even parity and 1 or 2 stop bits
  • Support Function Code 03 / 04 / 06 / 16 of Modbus functions for reading and writing J1939 Messages

 

Chia sẻ:
Model: GW-7228-G CR
Views: 655

Bộ chuyển đổi cổng J1939 sang Modbus RTU Slave ICP DAS GW-7228-G CR

The GW-7228 is a solution that provides a protocol conversion between J1939 and Modbus RTU. For J1939 network, the GW-7228 supports PDU1, PDU2, broadcast and destination specific type of J1939 messages. From the view of Modbus RTU network, the GW-7228 is a Modbus RTU slave to reply the request from Modbus RTU master. We provide Utility software for users to configure the parameters of J1939 / Modbus RTU of the GW-7228. The application fields can be Diesel power-train applications, In-Vehicle networks for trucks and buses, etc.
The following figure shows the application architecture for the GW-7228

• Diesel power-train applications
• In-Vehicle networks for trucks and buses
• Truck-Trailer connections
• Fleet management systems
• On Board Diagnostics
• Vehicle Automation\

LED Indicators
Status PWR / J1939 / MODBUS
COM Ports
Ports 1 x RS-232(TXD, RXD, GND)
1 x RS-422(Tx+, Tx-, Rx+, Rx-)
1 x RS-485(D+, D-)
Baud Rate 9600, 19200, 38400, 57600, 115200
Protocol Modbus RTU
J1939
Transceiver NXP 82C250
Ports 1
Baud Rate 250k
Isolation 3000 VDC power protection on CAN side, 2500Vrms photo-couple isolation on CAN bus
Terminal Resistor Jumper for 120 Ω terminal resistor
Specification ISO-11898-2, CAN 2.0A and CAN 2.0B
Pin Assignment C.I.A. DS-102 (CAN_H=7, CAN_L=2)
Power
Consumption 1.5 W
Mechanical
Dimensions (mm) 108 x 72 x 35 (H x W x L)
Installation DIN-Rail
Environmental
Operating Temperature -25 ~ +75 ℃
Storage Temperature -30 ~ +80 ℃
Humidity 10 ~ 90% RH, Non-condensing
  • Provide Modbus network configuration interface
  • Provide J1939 network configuration interface – Network Address / Device Name…
  • Provide J1939 Input / Output configuration interface

Comparison Table

ICP DAS Fieldbus Gateways Comparison Table:
Model Support Protocol Comm. Interface
GW-7228 J1939 Modbus RTU Slave RS-232
RS-422
RS-485
GW-7433D CANopen Master Modbus TCP server/RTU Slave RS-232
RS-485
Ethernet
I-7231D CANopen Slave DCON Master RS-232
RS-485
I-7232D CANopen Slave Modbus RTU Master RS-232
RS-485
I-7241D DeviceNet Slave DCON Master RS-232
RS-485
I-7242D DeviceNet Slave Modbus RTU Master RS-232
RS-485
I-7243D DeviceNet Master Modbus TCP server Ethernet
GW-7243D DeviceNet Slave Modbus TCP/RTU/ASCII Master RS-232
RS-485
Ethernet
GW-7552 PROFIBUS DP-V0 Slave Modbus RTU/ASCII
Master/Slave		 RS-232
RS-422
RS-485
GW-7553 PROFIBUS DP-V0 Slave Modbus TCP/RTU/ASCII Master/Slave RS-232
Ethernet
HART-710 HART Master Modbus RTU/ASCII Slave RS-232
RS-422
RS-485
GW-7228-G     CR J1939/Modbus RTU Slave Gateway included CA-0910 cable(RoHS)
Data Sheet
TOP HOME